製品

DN6000k10

DN6000k10
VirtexII™-Pro Based
ASIC Prototyping Engine

  • USB-based hosted logic prototyping system
    • Available with up to 9 VirtexII-Pro FPGAs (FF1704 BGA)
      • 2VP70 (-5, -6, -7) or
      • 2VP100 (-5, -6) or
  • Twelve DDR SDRAMs with 2VP100 (standard: 32M x 16)
    • Options for 64M x 16 DDR devices
    • 2 DDRs connected to FPGAs A, C, D, F, G, I
  • Five 64 Mbit (4M x 16) FLASH devices for PowerPC code storage
    • Connected to FPGAs A, B, C, G, I
  • Large, high-speed busses between FPGAs facilitate the logic partitioning process
  • RocketI/O connections between FPGAs enables high speed data movement
  • Two PowerPC 405 Cores per FPGA (18 total with nine FPGAs)
    • Embedded 300+ MHz Harvard Architecture
    • Hardware Multiply/Divide Unit
    • Thirty-Two 32-bit General Purpose Registers
    • 16 KB 2-Way Set-Associative Instruction Cache
    • 16 KB 2-Way Set-Associative Data Cache
    • Memory Management Unit (MMU)
    • Timer Facilities
  • Dedicated external JTAG connectors for uP trace/debug on FPGAs A & C
  • Six RS232 ports for PowerPC observation/debug
    • Four full duplex (RX/TX)
    • Two Single duplex (TX only)
    • All six ports multiplexed via SpartanII Configuration FPGA
  • Flexible, abundant, and configurable embedded memory in FPGAs:
    • 444 18-kbit memory blocks per FPGA (2VP100)
    • Up to 1.378 Kbytes Distributed SelectRAM per FPGA (2VP100)
    • 100% available for user applications
    • Direct support for TDM interconnect multiplexing
  • 20A on-board switching regulator for both +2.5V and +1.5V
  • Standalone operation
    • Uses an off-the-shelf ATX power supply
  • Status LEDs provide instant status and operational feedback
  • Fast/Easy FPGA configuration via standard SmartMedia FLASH card
    • Microprocessor controlled (CY7C68013)
    • Separate RS232 port for configuration/operational status and control
    • Fastest possible configuration using SelectMap
    • Nine 2VP100s configures in less than 7 seconds
    • Sanity checking programs for bit files simplify the configuration process
  • 5 low skew clocks distributed to all FPGAs and headers (from up to 8 possible sources):
    • 2 socketed oscillators
    • 1 clock dividable via CPLD
    • 4 external clocks via ribbon cable (may be differential!)
    • 2 CY7B993/4 RoboClockII PLLs
  • Robust observation/debug with 480+ connections for logic analyzer observability and pattern generator stimulus. Fully compatible with:
    • DNPMC104 — Embedded Systems Board Carrier (ESBC)
      • PMC and PC/104+ cards
    • DN3k10SD – Observation Daughter Card
    • DN3k10SD_MICTOR – Observation Daughter card with Mictor connectors
  • Custom daughter PWB for application specific circuitry and interfaces
  • 8 off-board, RocketI/O-based high speed serial ports
    • SMA Connectors (2 MGTs each)
    • 2 ports each connected to FPGAs A, C, G, I
  • Boatloads of reference stuff included (FREE)
    • DDR SDRAM controller (Verilog/VHDL)
    • PowerPC “Hello World”
    • UART’s
    • USB utilities
    • Board test(s)
    • USB Drivers (with C code)
      • Windows XP, ME, 2000, 98, NT
      • LINUX, Solaris
  • Full support for embedded logic analyzers via JTAG interface
    • ChipScope, ChipScope PRO
    • Identify from Synplicity
  • We recommend using the Daughter Card Extender when using 200-pin daughtercards.

Overview

The DN6000k10 is a complete logic emulation system that enables ASIC or IP designers to prototype logic and memory designs for a fraction of the cost of existing solutions. The DN6000k10 is stand-alone or hosted via a USB interface.

A single DN6000k10 configured with nine 2VP100s can emulate up to 6 million gates of logic as measured by LSI. And this number does not include the embedded memories and multipliers resident in each FPGA.

The DN6000k10 achieves high gate density and allows for fast target clock frequencies by utilizing FPGAs from Xilinx’s VirtexII-Pro family for logic and memory. High I/O-count, 1704-pin, flip-chip BGA packages are employed providing for abundant, fixed interconnect between the FPGAs. RocketI/Os are connected between FPGAs, enabling data transfer between FPGAs on the order of gigabytes per second. A total of 480+ test pins are provided on the top of the PWB for logic analyzer-based debugging, or for pattern generator stimulus. The DNPMC104 card can be mounted to any of these connectors, enabling an interface to A/Ds, D/As, and a host of other embedded system peripherals.

Also, custom daughter cards can be mounted to these connectors as a means to interface the DN6000k10 to application-specific circuits. Eight RocketI/O ports are reserved for high-speed serial off-board interfaces. Reference material such as DDR SDRAM controllers, flash controllers, and PowerPC code is included (in Verilog, VHDL, C) at no additional cost.

Easy Configuration Via SmartMedia

The configuration bit files for the FPGAs are copied onto a 32/64/128-megabyte SmartMedia FLASH card (provided) and an on-board Cypress microprocessor controls the FPGA configuration process. FPGA configuration can also be controlled via the USB interface. Visibility into the configuration process is enhanced with an RS232 port. Sanity checks are performed automatically on the configuration bit files, streamlining the configuration process. FPGA configuration occurs at the fastest possible SelectMap frequency – 48MHz. Multiple LEDs provide instant status and operational feedback.

Related Documents

Related Resources