製品

DN6000k10SC

DN6000k10SC
VirtexII™-Pro Based
ASIC Prototyping Engine

  • 32/64-bit, +3.3V, PCI/PCIX-based PWB.
  • Single VirtexII-Pro FPGA in FF1152
    • 2vp20, 2vp30, 2vp40, or 2vp50
  • Two external independent SSRAMs
    • 512k/1M/2M x 36
    • pipeline or flowthrough
    • ZBT or non-ZBT
  • Two independent DDR SDRAM banks
    • 4 banks 32M/64M x 16
  • One independent external FLASH memories
    • 8M/16M x 16
  • 4 High Speed serial channels
    • 4 MGT’s (16 SMB connectors)
  • One 200-pin high-speed connectors for awesome signal integrity
    • custom daughter cards
    • observation daughter cards (such as DN3k10SD or DNPMC104)
  • 5A onboard linear regulator for +1.5V
    • +1.5V @ Switcher Module
    • +2.5V @ 10A Switcher Module
    • +2.5V @ 10A Switcher Module
  • One PowerPC 405 Cores
    • Embedded 300+ MHz Harvard Architecture
    • Hardware Multiply/Divide Unit
    • Thirty-Two 32-bit General Purpose Registers
    • 16 KB 2-Way Set-Associative Instruction Cache
    • 16 KB 2-Way Set-Associative Data Cache
    • Memory Management Unit (MMU)
    • Timer Facilities
    • Two dedicated external JTAG connectors for uP trace/debug
  • Four RS232 ports for PowerPC processor visibility
    • 2 Tx/Rx
    • 1 Tx only
  • Standalone operation via separate power connector
    • +3.3V not needed on backplane
  • Fast/Easy FPGA configuration via standard SmartMedia FLASH card
    • Microprocessor controlled (Atmega128L)
    • RS232 port for configuration/operational status and control
    • Fastest possible configuration using SelectMap parallel
      • 2vp50 configures in 1 second
    • Sanity checking programs for bit files eases configuration hassles
  • 6 low skew clocks distributed to FPGAs and test connector:
    • 2 CY7B994 RoboClockII PLLs for the best clock distribution
    • 1 FCT3805 low-skew clock driver (non-PLL)
    • 2 user-selectable socketed oscillators
    • PCI/PCI-X clock
    • 1 dividable clock via CPLD
  • Boatloads of reference stuff included (FREE)
    • 32-bit target PCI design (Verilog/VHDL)
    • 32-bit master/target OpenCore PCI (Verilog)
    • SDRAM controller (Verilog/VHDL)
    • DDR SDRAM controller (Verilog/VHDL)
    • PowerPC ‘Hello World’
    • UARTs
    • DOS-based utilities
    • Board test(s)
    • PCI Drivers (with C code)
      • Windows XP, ME, 2000, 98, NT
      • LINUX, Solaris
  • Full support for embedded logic analyzers
    • ChipScope, ChipScope PRO
    • Identify™ from Synplicity
  • 162 signals for observation/debug
    • Fully compatible with the DN3k10SD & DNPM104

Overview

The DN6000k10SC is a complete logic emulation system that enables ASIC or IP designers to prototype logic, memory, and embedded systems designs for a fraction of the cost of other solutions. The DN6000k10SC can be hosted in 32/64-bit PCI/PCIX slot, or can be used standalone. A DN6000k10SC can emulate up to 450,000 gates of logic as measured by LSI. In addition, the VirtexII Pro FPGA contains one 300MHz+ 405 PowerPC microprocessor, 88-232 18×18 multipliers, and more than 438 Kbytes of block RAM memory. Eight serial RocketI/O ports are provided on the top of the circuit board and can support a variety of serial communication protocols at speeds up to 3.125 GB/s, with 10 GB/s to follow. The DN6000k10SC is designed for performance and low cost – all external memories run at a frequency of at least 133MHz and the FPGA internal speed is limited only by the logic within. A high I/O count, 1152-pin BGA package is employed allowing for a host of external interface features including test signals, two SSRAMs, two DDR SDRAMs, and one FLASH. A total of 162 signals are provided via a 200-pin connector on the top of the PWB for logic analyzer-based debugging, or for pattern generator stimulus. Custom daughter cards can be mounted to this connector to interface the DN6000k10SC to application-specific circuits. A reference 32-bit PCI target design and test bench is provided (in Verilog/VHDL) at no additional cost.

Easy Configuration Via SmartMedia

The configuration bit file for the FPGA is copied onto a 32/64/128-megabyte SmartMedia FLASH card (provided) and an on-board microprocessor controls the FPGA configuration process. An RS232 port provides detailed information regarding the configuration process, completely bypassing time-consuming debugging of the configuration process. FPGA configuration occurs at close to the fastest possible parallel frequency –48MHz. Eight LEDs provide instant status and operational feedback. Two of these LEDs are connected to the CPLD and can be user-configured.

Top View

Bottom View


FPGA and Memory

SMB Connectors

Power


Related Documents

Related Resources