製品

DN9000K10

DN9000K10 Bride of Monster
Xilinx Virtex-5 Based ASIC Prototyping Engine

Link to block diagram showing interconnect with LX110/LX155/LX220 installed

  • USB2.0-hosted logic prototyping system with 2-16 Xilinx Virtex-5 FPGAs
    • 16 LX330s (FF1760)
    • 100% FPGA resources available for user application
  • 32M+ ASIC gates (LSI measure) with 16 LX330s
  • FPGA to FPGA interconnect is single-ended or LVDS
    • 450 MHz differential chip-to-chip DDR (900Mb/s)
  • Reference designs for integrated I/O pad ISERDES/OSERDES
    • 10x FPGA to FPGA pin multiplexing per LVDS pair
    • Greatly simplified logic partitioning
    • Source synchronous clocking for LVDS
    • Main Busses for global connectivity:
      • Main Bus Horizontal (MBH), all FPGAs: 80 single-ended signals
      • Main Bus Vertical (MBV), right two columns of FPGAs: 80 single-ended signals
  • Auspy AES models for partitioning assistance
    • Hooks for other third-party partitioning solutions
  • 6 separate DDR2 SODIMMs (250MHz)
    • 64-bit data width, 250MHz operation
    • PC2-5300
    • Addressing/power to support 4GB in each socket
    • DDR2 Verilog/VHDL reference design provided (no charge)
    • DDR2 SODIMM data transfer rate: 32Gb/s
    • Alternate pin compatible memory cards available:
      • QDR SSRAM, Mictor, RLDRAM, SSRAM, DDR3, DDR1, interconnect, SDRAM DRAM, FLASH and others
  • SODIMM Daughtercard expansion
  • 4 board-level global clock networks (GCLK0, GCLK1, GCLK2, REFCLK)
    • Separate programmable synthesizers for each network
    • User configurable via Compact FLASH or USB
    • Separate global reference clock network for IDELAY chain delay resolution (REFCLK)
    • Global clocks networks distributed differentially and balanced
    • Single-step clocking available on each global clock network
    • 3 external differential clock inputs can be multiplexed in to global clock networks (via SMAs)
  • 8, 400-pin MEG-Array connectors (FCI)
    • 96 LVDS pairs + clocks (or 192 single-ended)
    • 450MHz on all signals with LVDS
    • Reset, presence detect
    • Supplied power rails (fused):
      • +12V (24W max)
      • +5V (10W max)
      • +3.3V (10W max)
    • Pin multiplexing to/from daughter cards using ISERDES/OSERDES and LVDS (up to 10x)
  • Fast and Painless FPGA configuration
    • Compact FLASH, and/or USB
    • Integrated sanity checks on configuration files
    • Accelerated configuration readback
  • 4 separate parallel readback busses
  • Custom base plate (standard) and optional rackmount chassis
    • Provides protection from those drooling engineers
  • 4, RS232 ports for MicroBlaze or embedded uP debug
    • Accessible from all FPGAs via Configuration FPGA
  • Full support for embedded logic analyzers via JTAG interface
    • ChipScope, ChipScope Pro and other third party tools
  • Convert a pair of MEG-Array expansion connectors to interconnect with the DNMEG_Intercon.
    • Add 186 single-ended OR 93 pairs LVDS:
      • (FPGA 8 to 12)
      • (FPGA 3 to 7) AND/OR (FPGA 11 to 15)
  • MEG-Array Daughtercard Expansion
  • Enough status LEDs to perform a cosmetic peel on the face of a walrus

Overview

The DN9000k10 is a complete logic emulation system that enables ASIC or IP designers to prototype logic and memory designs for a fraction of the cost of existing solutions. The DN9000k10 is stand-alone or hosted via a USB interface. A single DN9000k10 configured with 16 Xilinx Virtex-5, LX330s can emulate up to 32 million gates of logic as measured by LSI. This number does not include the embedded memories and multipliers resident in each FPGA. The DN9000k10 achieves high gate density and allows for fast target clock frequencies by utilizing FPGAs from Xilinx’s Virtex-5 FPGA family for logic and memory. All FPGA resources are available for the target application. Any subset of FPGAs can be stuffed and each FPGA position can be stuffed with any available speed grade.

Virtex-5 FPGAs from Xilinx

High I/O-count, 1760-pin, flip-chip BGA packages are utilized. Abundant fixed interconnects are provided between the FPGAs. All pins of all banks of each FPGA are utilized. FPGA to FPGA busses are routed and tested LVDS, run at 450MHz+ (900 Mb/s) but can be used single-ended at a reduced speed. Example designs utilizing the integrated ISERDES/OSERDES with DDR for pin multiplexing are included. An 80-pin main bus horizontal (MBH) is connected to all FPGAs and another 80-pin Main Bus vertical (MBV) is connected to the 8 FPGAs in the right two columns. Bus switches on the MBH bus allow for higher performance operation when a subset of FPGAs is stuffed.

Daughter cards

The DN9000k10 is easily adaptable to all applications via daughter cards. Eight separate 400-pin FCI MEG-Array connectors allow for customization via expansion. Signals to/from these cards are routed differentially and can run at the limit of the FPGA: 450MHz. Clocks, resets, and presence detection, along with abundant (fused) power are included in each connector. Signals are routed from the FPGAs on a bank basis, and the daughter card selects the I/O voltage of the connector by driving the VccI/O of the FPGA bank. The I/O voltage ranges are +1.5V to +3.3V. The DNMEG_Intercon card can be used to convert any or all of these connectors to interconnect.

Memory

Six separate DDR2 SODIMM sockets are connected to FPGAs 0, 1, 2, 12, 13, and 14. Each socket is tested to 250MHz with a DDR2 SODIMM. Standard, off-the-shelf DDR2 memory DIMMs (PC2-5300) work nicely and we can provide these for a small charge. We have developed alternative SODIMMs that can be stuffed into these positions. Consult the factory for more details, but the list includes FLASH, SSRAM, QDR SSRAM, RLDRAM, SDR SDRAM, mictors, DDR1, DDR3, and others.

Easy Configuration Via Compact Flash or USB

The configuration bit files for the FPGAs are copied onto a 128-megabyte Compact FLASH card (provided) and an on-board Cypress microprocessor controls the FPGA configuration process. FPGA configuration can also be controlled via the USB interface. Fully stuffed, the DN9000k10 configures in less than 60 seconds. Visibility into the configuration process is enhanced with an RS232 port. Sanity checks are performed automatically on the configuration bit files, streamlining the configuration process. FPGA configuration occurs at the fastest possible SelectMap frequency – 48MHz. Multiple LEDs provide instant status and operational feedback. Laboratory testing is showing that the amount of illumination provided by the LEDs is enough to perform sophisticated cosmetic procedures on a walrus. As always, reference material such as DDR2 SDRAM controllers, flash controllers, et al. is included (in Verilog, VHDL, C) at no additional cost.

Optional 19″ Rackmount Chassis

The DN9000k10 comes standard mounted to a base plate. An optional 19″, 4U-high Rackmount chassis is available. The photos on the following pages show the DN9000k10 installed in this optional chassis. The top plate is not shown. The chassis is shipped with a Zippy Technology Corporation power supply rated at 600 watts with an AC input voltage range of 100~240 VAC. The front panel has an LCD display with an ON/OFF switch for power, and momentary switches for HARD RESET and LOGIC RESET. On the front panel connectors support the following functions: MCU RS232-FPGA configuration and control USB-Hosting and/or FPGA configuration User RS232 (2,3,4)-User RS232 ports (requires UART in FPGA)

Specs of FPGAs Available on the DN9000K10

Chassis Pictures

Related Documents

Related Resources

Alternate Memory: